验货感应灯时，需要从外观、功能、安全性等多个方面进行检查，以确保产品符合质量标准和客户的要求。以下是详细的感应灯验货步骤：

1. 外观检查

外壳状况：检查感应灯外壳是否有划痕、裂缝、变形等明显的损坏或瑕疵。

颜色一致性：确保灯体颜色均匀，无明显色差。

零件完整性：检查灯具各个部件是否齐全，如灯罩、底座、感应器等。确保各个连接部位牢固无松动。

清洁度：确保表面干净，无油污、灰尘或其他杂物。

2. 功能测试

感应功能：

感应范围：测试感应灯的感应距离和角度。使用身体或手移动来模拟触发感应，确保感应器在规定范围内能够准确探测到运动。

感应灵敏度：检查感应灯的灵敏度，确保在感应距离内能够迅速响应并点亮。

延时关闭功能：测试感应灯的延时功能，观察灯是否在设定的时间内自动关闭，并确保延时功能符合说明书的描述（例如几秒或几分钟）。

光照强度：使用照度计或肉眼观察感应灯的亮度，确保亮度符合产品规格。

模式切换测试：如果感应灯具有不同的模式（如夜间模式、节能模式等），逐个进行切换测试，确保每种模式正常运行。

3. 电气性能测试

功率测试：使用功率计测试感应灯的功率，确保功率值与标注的额定功率一致。

电压测试：检查感应灯在不同电压条件下是否能正常工作，特别是在额定电压下的稳定性。

电源线检查：确保电源线无破损、连接牢固，插头正常使用。

耗电情况：对于节能型感应灯，测试其耗电量，确保在低耗电的同时能正常工作。

4. 安全性检查

防水性能：如果是户外感应灯，需要进行防水测试（IP等级），确保灯具在暴露于雨水或潮湿环境下不会进水或损坏。

绝缘和漏电测试：使用绝缘电阻测试仪检测感应灯的绝缘性能，确保不会发生漏电风险。必要时进行接地电阻测试，确保符合安全标准。

过热保护功能：测试感应灯长时间工作时，是否具备过热保护功能，检查其散热效果，确保不会因为过热而损坏或引发火灾风险。

5. 光感检测

日夜感应测试：如果感应灯具备光感功能，应在不同光照条件下（明亮和黑暗环境）测试感应灯的反应，确保白天不亮、夜晚才启动。

环境适应性：测试在不同光照条件下，感应灯是否能正确感应光线并启动。

6. 耐用性与可靠性测试

开关寿命测试：通过多次启闭感应灯，模拟日常使用，确保其在反复使用的情况下，灯具和感应器都能正常工作且无故障。

跌落测试：对便携式或移动式感应灯进行低高度（如1米）跌落测试，检查其在受到外部冲击后是否还能正常工作，外壳是否出现裂缝或破损。

7. 包装与配件检查

包装完整性：检查包装是否牢固，防护措施是否到位（如泡沫、塑料袋、说明书等），以确保运输过程中不会损坏。

配件齐全：确认所有配件是否齐全，例如螺丝、安装支架、充电线（如为充电款式），并核对说明书中的配件清单。

标识清晰度：检查包装及产品本身的标签，确保有清晰的产品名称、型号、功率、生产日期、认证标志（如CE、FCC等）等信息。

通过上述验货步骤，可以确保感应灯的质量、安全性和功能性达到要求，并能有效使用。

Inspecting an induction (sensor-based) light involves checking its functionality, safety, durability, and overall quality. Here's a step-by-step guide to properly inspect an induction light:

1. Visual Inspection

Housing Condition: Examine the      light's exterior for any visible damage, such as cracks, dents, or      scratches. The housing should be intact, without any deformation or sharp      edges.

Color Consistency: Ensure the      light’s housing has consistent color and finish across all units.

Component Completeness: Check if      all parts are present, such as the light cover, sensor, mounting brackets,      or power cables. Ensure these components are firmly attached.

Cleanliness: The exterior should be      free of dust, oil, or any visible debris.

2. Functional Testing

Sensor Functionality:

Detection Range: Test the       induction light’s sensor by moving within the stated detection range and       angle. Ensure the sensor responds accurately by turning the light on       within the designated range.

Sensor Sensitivity: Test the       light's sensitivity by varying the distance and speed of movement in       front of the sensor to check if it activates as intended.

Auto-off Timer: After activation,       measure the time it takes for the light to turn off. Ensure the delay       matches the specified settings (e.g., 30 seconds, 1 minute).

Lighting Performance:

Brightness: Use a lux meter to       measure the light output and ensure the brightness is within the       product's specifications.

Light Spread: Observe the light       distribution to ensure it spreads evenly without dark spots or shadows.

Mode Settings: If the light offers      different modes (e.g., night mode, energy-saving mode), switch between      them and verify each mode works as expected.

3. Electrical Testing

Power Consumption: Use a power      meter to verify the induction light’s power consumption matches the      manufacturer’s stated values.

Voltage Stability: Check the      light’s operation at different voltage levels (particularly the rated      voltage) to ensure it functions without flickering or shutdowns.

Cable and Plug: Inspect the power      cord for damage or weak points. Ensure the plug is securely connected and      functions correctly.

Energy Efficiency: For      energy-efficient lights, verify their power consumption aligns with      energy-saving standards.

4. Safety Testing

Waterproofing (for Outdoor Lights):      If the induction light is intended for outdoor use, perform an IP rating      test (e.g., IP65 for water resistance) by spraying water to ensure it      remains operational without water intrusion.

Electrical Insulation: Test the      light’s insulation resistance using an insulation tester to ensure there’s      no risk of electrical shock or short circuit.

Leakage Current Test: Perform a      leakage current test to ensure the light does not have excessive      electrical leakage, which could pose a safety risk.

Overheat Protection: Run the      induction light for an extended period and monitor its temperature. Ensure      that it doesn’t overheat or pose a fire hazard. Some lights come with      built-in overheat protection features—test this by intentionally allowing      the light to reach higher temperatures.

5. Environmental and Sensitivity Testing

Day/Night Sensor Testing: If the      light has a built-in light sensor, test it by simulating different light      conditions (daylight and darkness) to ensure the light only activates at      night or in low-light conditions.

Environmental Adaptability: Test      the light in various conditions, such as extreme heat, cold, or humidity,      to ensure it performs reliably in different environments, especially for      outdoor lights.

6. Durability and Reliability Testing

Switch Cycle Test: Test the light’s      durability by turning it on and off multiple times (simulating normal      use). Ensure the sensor and light respond consistently.

Drop Test: For portable or      lightweight induction lights, drop the unit from a low height (e.g., 1      meter) to see if it can withstand shocks without damage or malfunction.

Long-Running Test: Let the light      run for an extended period to test for overheating, flickering, or sudden      shutdowns.

7. Packaging and Accessories

Packaging Quality: Inspect the      packaging for sturdiness and sufficient protective material to ensure the      product will not be damaged during shipping.

Accessory Check: Verify that all      accessories are included, such as mounting brackets, screws, a power      adapter (if applicable), and user manuals.

Labels and Certifications: Ensure      the packaging includes important product information, such as product      name, voltage, power rating, and safety certifications (e.g., CE, UL,      FCC).

8. Weight and Build Check

Weight Check: Weigh the induction      light to ensure it matches the product specifications.

Build Quality: Test the sturdiness      of the materials. The light should not feel flimsy, and all parts should      fit together well without rattling or gaps.

By following these steps, you can ensure that the induction light meets quality standards and performs its intended functions safely and efficiently.

Inspecting an induction (sensor-based) light involves checking its functionality, safety, durability, and overall quality. Here's a step-by-step guide to properly inspect an induction light:

1. Visual Inspection

Housing Condition

Color Consistency

Component Completeness

Cleanliness

2. Functional Testing

Sensor Functionality:

Detection Range

Sensor Sensitivity

Auto-off Timer

Lighting Performance:

Brightness

Light Spread

Mode Settings

3. Electrical Testing

Power Consumption

Voltage Stability

Cable and Plug

Energy Efficiency

4. Safety Testing

Waterproofing (for Outdoor Lights)

Electrical Insulation: Test the light’s      insulation resistance using an insulation tester to ensure there’s no risk      of electrical shock or short circuit.

Leakage Current Test

Overheat Protection

5. Environmental and Sensitivity Testing

Day/Night Sensor Testing

Environmental Adaptability

6. Durability and Reliability Testing

Switch Cycle Test

Drop Test

Long-Running Test

7. Packaging and Accessories

Packaging Quality

Accessory Check

Labels and Certifications

8. Weight and Build Check

Weight Check

Build Quality

By following these steps, you can ensure that the induction light meets quality standards and performs its intended functions safely and efficiently.